翻訳と辞書
Words near each other
・ Tentacle (botany)
・ Tentacle (disambiguation)
・ Tentacle erotica
・ Tentacle Ridge
・ Tentacled blenny
・ Tentacled dragonet
・ Tentacled flathead
・ Tentacles (album)
・ Tentacles (film)
・ Tentacles (novel)
・ Tentacles Convention
・ Tensift
・ Tensift River
・ Tensigh
・ Tensile structure
Tensile testing
・ Tensilica
・ Tensilica Instruction Extension
・ Tensin
・ Tensing Pen Resort
・ Tensiometer
・ Tensiometer (soil science)
・ Tensiometer (surface tension)
・ Tensiomyography
・ Tension
・ Tension (band)
・ Tension (Die Antwoord album)
・ Tension (Dizmas album)
・ Tension (film)
・ Tension (geology)


Dictionary Lists
翻訳と辞書 辞書検索 [ 開発暫定版 ]
スポンサード リンク

Tensile testing : ウィキペディア英語版
Tensile testing

Tensile testing, also known as tension testing, is a fundamental materials science test in which a sample is subjected to a controlled tension until failure. The results from the test are commonly used to select a material for an application, for quality control, and to predict how a material will react under other types of forces. Properties that are directly measured via a tensile test are ultimate tensile strength, maximum elongation and reduction in area. From these measurements the following properties can also be determined: Young's modulus, Poisson's ratio, yield strength, and strain-hardening characteristics.〔.〕 Uniaxial tensile testing is the most commonly used for obtaining the mechanical characteristics of isotropic materials. For anisotropic materials, such as composite materials and textiles, biaxial tensile testing is required.
==Tensile specimen==

A tensile specimen is a standardized sample cross-section. It has two shoulders and a gage (section) in between. The shoulders are large so they can be readily gripped, whereas the gauge section has a smaller cross-section so that the deformation and failure can occur in this area.〔〔.〕
The shoulders of the test specimen can be manufactured in various ways to mate to various grips in the testing machine (see the image below). Each system has advantages and disadvantages; for example, shoulders designed for serrated grips are easy and cheap to manufacture, but the alignment of the specimen is dependent on the skill of the technician. On the other hand, a pinned grip assures good alignment. Threaded shoulders and grips also assure good alignment, but the technician must know to thread each shoulder into the grip at least one diameter's length, otherwise the threads can strip before the specimen fractures.〔
In large castings and forgings it is common to add extra material, which is designed to be removed from the casting so that test specimens can be made from it. These specimens may not be exact representation of the whole workpiece because the grain structure may be different throughout. In smaller workpieces or when critical parts of the casting must be tested, a workpiece may be sacrificed to make the test specimens.〔.〕 For workpieces that are machined from bar stock, the test specimen can be made from the same piece as the bar stock.
The repeatability of a testing machine can be found by using special test specimens meticulously made to be as similar as possible.〔
A standard specimen is prepared in a round or a square section along the gauge length, depending on the standard used. Both ends of the
specimens should have sufficient length and a surface condition such that they are firmly gripped
during testing. The initial gauge length Lo is standardized (in several countries) and varies with the
diameter (Do) or the cross-sectional area (Ao) of the specimen as listed
The following tables gives examples of test specimen dimensions and tolerances per standard ASTM E8.


抄文引用元・出典: フリー百科事典『 ウィキペディア(Wikipedia)
ウィキペディアで「Tensile testing」の詳細全文を読む



スポンサード リンク
翻訳と辞書 : 翻訳のためのインターネットリソース

Copyright(C) kotoba.ne.jp 1997-2016. All Rights Reserved.